goods
Rexroth type switching electromagnet

locationHome > Products > Rexroth type switching electromagnet
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
Rexroth type switching electromagnet MFZ6-37YC
model MFZ6-37YC
Rated voltage(V) 12 24 110 220
Rated suction (N) ≥37
Rated stroke (mm) 2.8
Full stroke (mm) ≥6.1
Email
Tel
Description
The electromagnet is applicable to the direct power supply with single-phase bridge full wave rectification and the control circuit with voltage up to 220V. It is used as the power element of the hydraulic electromagnetic directional valve. The product is licensed by BSO Control Technology Co., Ltd. and is matched with Rexroth six and ten diameter screw connected solenoid directional valve。 Normal operating conditions ● It can be installed in any direction。 ● There shall be no gas and dust that can corrode metal and damage insulation in the service environment. Otherwise, the service life of the product may be affected。 ● Electromagnet is suitable for long-term working system and intermittent periodic working system。 ● The reasonable fluctuation range of power supply voltage is 85% - 110% (special requirements can be put forward when ordering)。 ● Enclosure protection Class IP65。
Parameters

    Main technical parameters

model    

MFZ6-37YC

Rated voltage(V)

12 24 110 220

Rated suction(N) 

≥37

Rated stroke(mm)

2.8

Full stroke(mm)

≥6.1

Power consumption(W)

≤30

Withstand static oil pressure(Mpa)

21

Operating frequency (T/h)

12000

     

    Order code

Valve electromagnet

direct

Design serial number

Rated suction(N)

Wet

MF

Z

6

37

YC

     

    Stroke force characteristic curve

     

    Anyang Kaidi Magnetic Technology Co., Ltd

     

     

    Outline and installation dimensions

    product model:MFZ6-37YC

     

    Anyang Kaidi Magnetic Technology Co., Ltd

     

     

    Precautions for use

    ●  The electromagnet adopts half wave rectifier AC power socket conforming to iso4400 standard. The voltage specification must be consistent with the voltage specification of the electromagnet body。

    ●  The manual push rod of the electromagnet is used for manual control during commissioning or in case of emergency. However, when the back pressure of the system is high and it is difficult to adjust, please use a cross screwdriver to slowly push the manual push rod. Impact force should not be used to avoid damaging the surface of the manual push rod and the guide inner hole, resulting in oil leakage of the electromagnet or failure to reset。

    ●  When the electromagnet is used in two directions, it must be ensured that the two electromagnets cannot be energized at the same time, so as to prevent the electromagnet from working normally。

    ●   An overcurrent protection device shall be set between the electrical control system and the connecting part of the electromagnet to avoid burning the electromagnet and your electric control components under abnormal conditions。

     

    Sample description

  •             If customers have different needs, under the condition that the performance of the electromagnet remains unchanged, the connection size between the electromagnet and the valve body, the extension length of the push rod and the working power supply voltage can be adjusted according to requirements。

  •             The characteristic curve is for reference only。

  •             The main performance parameters are obtained under the test conditions. The company reserves the right to modify parameters。


Inquiry
Email:
top