email aykd_scb@126.com   
tel +86-372-2595077/2595078/2595088
goods
Oil grinding type switching electromagnet

locationHome > Products > Oil grinding type switching electromagnet
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
Oil grinding type switching electromagnet MFJ10-28YC
model  MFJ10-28YC
Rated voltage(V) 110 220
Power frequency (Hz) 50
Rated suction(N) ≥28
Rated stroke(mm) 3
Email aykd_scb@126.com
Tel +86-372-2595077/2595078/2595088
Description
This series of electromagnets is applicable to the control circuit with AC 50Hz and voltage up to 380V. It is used as the power element of hydraulic electromagnetic directional valve. It can be matched with six or ten diameter junction box threaded solenoid directional valve。 Normal operating conditions ● It can be installed in any direction。 ● There shall be no gas and dust that can corrode metal and damage insulation in the service environment. Otherwise, the service life of the product may be affected。 ● Electromagnet is suitable for long-term working system and intermittent periodic working system。 ● The reasonable fluctuation range of power supply voltage is 85% - 110% (special requirements can be put forward when ordering)。 ● Enclosure protection Class IP65。
Parameters

Related parameters

model  

MFJ10-28YC

Rated voltage (V)

110 220

Power frequency (Hz)

50

Rated suction (N)

≥28

Rated stroke (mm)

3

Full stroke (mm)

≥6

Withstand static oil pressure(Mpa)

16

Starting voltammetry(VA)

≤188

Holding voltammetry (VA) 

≤60

Operating frequency (T/h)

12000

     

Order code

Valve electromagnet

direct

Design serial number

Rated suction(N)

Wet

MF

J

10

28

YC

Stroke force characteristic curve

    Anyang Kaidi Magnetic Technology Co., Ltd

     

     

     

    Outline and installation dimensions

    product model:MFJ10-28YC

     

    Anyang Kaidi Magnetic Technology Co., Ltd

     

     

     

     

    Precautions for use

    ●  The wiring mode of electromagnet is junction box type. The voltage specification of the junction box must be consistent with the voltage specification of the electromagnet body。

    ●  The manual push rod of the electromagnet is used for manual control during commissioning or in case of emergency. However, when the back pressure of the system is high and it is difficult to adjust, please use a cross screwdriver to slowly push the manual push rod. Impact force should not be used to avoid damaging the surface of the manual push rod and the guide inner hole, resulting in oil leakage of the electromagnet or failure to reset。

    ●  When two-way electromagnets are used, it must be ensured that the two electromagnets cannot be energized at the same time, so as to prevent the solenoid valve from working normally。

    ●   An overcurrent protection device shall be set between the electrical control system and the connecting part of the electromagnet to avoid burning the electromagnet and your electric control components under abnormal conditions。

     

    Sample description

    If customers have different needs, under the condition that the performance of the electromagnet remains unchanged, the connection size between the electromagnet and the valve body, the extension length of the push rod and the working power supply voltage can be adjusted according to requirements。

    The characteristic curve is for reference only。

    The main performance parameters are obtained under the test conditions. The company reserves the right to modify parameters。


Inquiry
Email:aykd_scb@126.com
Yu ICP Bei No. 2022007958-1
Yugong Anbei No.41050202000076
top